PVC ex-factory price, Jinhua Group loose 5 type calcium carbide method 6600 yuan (ton price, the same below), Tianjin chemical plant loose 3,5,7,8 6400 ~ 6500 yuan, Siping United 6600 yuan, Qihua Group 6300 yuan, Qilu Petrochemical Company S700 is 6700 yuan, S1000 is 6550 yuan. Compared with the first half of July, Jinhua and Tianjin all fell by 300 yuan, Qihuan fell by 500 yuan, Qilu fell by 50 yuan, Siping has not changed, and prices fell slightly.
Low density polyethylene ex-factory price, Lanzhou Petrochemical Company M13D (injection plastic) 10900 yuan; Daqing Petrochemical Company F18D (film material) 10900 yuan, 18E (re-packaging material) 10800 yuan, 18G (coating material) 11250 yuan, 19E (cable Materials) 11350 yuan; Yanshan Petrochemical Company 1F7B (film material) 11100 yuan, 1C7A (coating material) 11200 yuan, 1I50A (flower material) 11800 yuan, LD100AC (film material) 10900 yuan, LD160AS (film material) 11150 yuan, LD150 (Thin film material) 11250 yuan, LD165 (film material) 11400 yuan, LD100BW (cable material) 11300 yuan, LD605 (injection plastic) 10920 yuan; Qilu petrochemical company TN00/26 (thin film material) 10900 yuan. Compared with the first half of July, Lanzhou fell 400 yuan, Daqing F18D fell 200 yuan, the rest of the brand has not changed; Yanshan 1F7B rose 50 yuan, LD100BW rose 200 yuan, the remaining 7 brands have dropped 100 to 200 yuan; Qilu fell 300 yuan The price was slightly lower, and the price fell slightly.
HDPE ex-factory price, Fushun Petrochemical Company 2980, 2909 (plastic injection) 11000 yuan, 2911, 2909FS (injection plastic) 11050 yuan, 2911FS (injection plastic) 11100 yuan; Liaoyang Petrochemical Corporation L055P (plastic window packing) 11,500 yuan; Daqing Petrochemical Company 5000S (raw material), 5300B (battery material), 1600J (injection plastic) are 10,800 yuan, 2200J (injection plastic) 10,700 yuan, 5300E (cable material) 11,000 yuan; Lanzhou Petrochemical Company 5000S10900 yuan; Yanshan Petrochemical Company 5000S10700 yuan, 5200B (hollow material) 10350 yuan, 6100M (pipe) 10600 yuan; Qilu Petrochemical Corporation 6098 (film material) 10500 yuan, 1158 (large hollow material) 10900 yuan; 2480 (pipe) 10700 yuan; Dushanzi The company 6070 (injection plastic) 11400 yuan. Compared with the first half of July, Fushun fell 200 yuan, Daqing fell 100 to 200 yuan, Lanzhou fell 400 yuan, Yanshan fell 300 to 400 yuan, Qilu fell 200 to 450 yuan, Liaoyang, Dushanzi did not change, or more level less The price fell slightly.
Linear low density polyethylene ex-factory price, Jilin Chemical Company 7042 (pellets) 10610 yuan, Daqing Petrochemical Corporation 7042, 7047 (film material) 10600 yuan, Lanzhou Petrochemical Corporation 103AA (film material) 10400 yuan, Qilu Petrochemical Corporation 7042 (Ding E-grade material) 10,300 yuan, Dushanzi Petrochemical Company 0209 (film material) 10,600 yuan. Compared with the first half of July, Kyrgyzstan fell 50 yuan, Lanzhou, Qilu, Dushanzi fell 300 to 400 yuan, Daqing unchanged, down more than flat, the price fell slightly.
Polypropylene ex-factory price, Lanzhou Petrochemical Company F401 (raw material) 10,750 yuan; Liaoyang Petrochemical Company 5004 (raw material) 10950 yuan, 70218 (fiber material), 71735 (tobacco material for tobacco), 70126 (film coating material) are 11050 yuan; Daqing Petrochemical Company T30S (raw material) 10,900 yuan, T38F (film material) 11,000 yuan; Fushun Petrochemical Company T30S ex-factory price, 10850 yuan, T38F (film material), Z30S, H30S-2 (fiber material) are 10950 Yuan; Yanshan Petrochemical Company 2401 (raw material) 11,000 yuan, K8303 (injection plastic) 11,500 yuan, K7726 (washing machine-specific material) 11400 yuan, 4220 (pipe) 12710 yuan; Dushanzi Petrochemical Company T30S is 11,000 yuan, EPS30R (Note Plastic) 11,200 yuan; Jinzhou Petrochemical Company 10,500 yuan powder; Shijiazhuang refinery powder 10,600 yuan. Compared with the first half of July, Lanzhou fell 550 yuan; Liaoyang, Jinzhou fell 50 yuan; Fushun fell 150 yuan; Daqing fell 200 yuan; Yanshan 2401, K8303, K7726 fell 200 to 300 yuan, 4220 has not changed; Dushanzi fell 400 Yuan; Shijiazhuang has not changed. The pellets were more or less flat and the powder fell flat, and the price stopped falling. The mainstream price of drawing materials such as F401, 5004, T30S, and 2401 was 10750 to 11,000 yuan, a drop of 200 to 550 yuan, fiber material, film material, and injection plastic, and a drop of 50 to 150 yuan.
Polystyrene ex-factory price, Fushun Petrochemical Company 825 is 10,900 yuan, Daqing Petrochemical Company 200D is 11,300 yuan, Yanshan Petrochemical Company 666D is 11,400 yuan. Compared with the first half of July, Fushun and Daqing all fell by 400 yuan. Yanshan remained unchanged, and prices stopped falling.
ABS ex-factory price, Jilin Chemical Company 0215A is 14,210 yuan, Daqing Petrochemical Company 750A is 14,350 yuan, Lanzhou Petrochemical Corporation 301 is 14,600 yuan, 301W is 14,400 yuan. Compared with the first half of July, Jilin fell 300 yuan, Daqing fell 350 yuan, Lanzhou fell 100 yuan, a slight decline across the board.
The insulation breakdown accident often occurred in generator. It includes interphases short circuit, inter-turn short circuit and ground fault.
The interphase short circuit: the generator windings ends will be greatly impacted by electric power and may make the coil end deformed under two-phase or three-phase short circuit and differential protection tripping happening.
Inter-turn short circuit: Generator outlet blasting, if it continues a long time, the stator copper wire will be melted. When no-load run, the generator three-phase voltage will be imbalance.
Ground fault: Generator breakdown location is in the linear portion or notch position and stator ground protection act. The insulation resistance value between stator ground and ground is zero or minimum.
The fundamental reason of generator insulation breakdown is that the stator coil insulation is weak or there is a corona etching in notch in run time. The treatment method is to find the point of breakdown and reworked and reinforced insulation. At the same time, eliminating the corona etching in a maximum extent is important.
III. A large noise or vibration with generator
The reasons of a large noise or vibration with generator are:
1. Foundation bolts loose, or STG subsidence. Treatment: fastening bolts. Recalibration concentricity.
2. Generator rotor and Steam Turbine shaft are misalignment. Treatment: calibration concentricity.
3. Bearing wall worn or damaged under short oil. Treatment: repaired bearing or replace a new bearing with same model.
4. There is a friction between the stator and rotor. Treatment: find the friction location and reason, and then eliminate it.
5. Fan or other fasteners loose. Treatment: Tighten fan and fasteners.
6. Rotor coil partial short circuit, two points grounding or wiring errors. Treatment: please inspect the insulation of slip ring and the rotor coil to the ground. Or connect to the DC power source and check the voltage drop of each coil, winding direction and wiring method. So we can identify the cause of the malfunction and eliminate them.
7. Brush is too hard, or the pressure is too large. Treatment: adjust the pressure or replace the same type of brush.
8. Three-phase current are severe asymmetry. Treatment: please investigate that the three-phase current imbalance is in the allowable range or not. If it is not in the allowable range, please adjust three-phase load or reduce the load.
9. Stator winding short circuit or ground. Treatment: Find out the fault and repair it.
10. External fault or lightning strike. Treatment: if the vibration time is too long, please stop the STG and inspect.
Typical
cases:
This is a 15 MW generator from a Shandong customer. The vibration of generator is reached to 0.12mm in running. After inspection the generator, we found that rotor dynamic AC impedance upheaval 12% in 2400-2700 and the dynamic inter-turn short circuit is serious. It destroys the balance of the magnetic field and causes the electromagnetic force uneven of generator rotor. After removal of the rotor retaining ring and treatment the rotor inter-turns, we start the STG. The vibration is about 0.01mm.
IV. The temperature of a generator is too high.
Generally the temperature of a generator will be in the allowable value, if the generator running normally and the current, voltage, frequency, power, excitation current and power factor are all within the allowable fluctuation range. If a generator stator, core and other parts temperature are too high, please consider the following cases:
1. Generator overload operation and exceed the allowable time. Treatment: Please reduce the generator load to the rated load or under rated load as soon as possible.
2. Three-phase current are serious imbalance. Treatment: please find out the reason of imbalance. If it is the voltage causing, please check if it is the generator inter-turn short circuit. If it is load causing, please adjust the load and make it balance.
3. The ventilation cooling system of generator is poor. For example, the temperature is too high, the air duct or exhaust duct are blocked, the coil and its ends are serious fouling. Treatment: please reduce the load suitability, improve ventilation, and remove fouling.
4. The stator winding portion short circuit or ground. Treatment: Find out the short circuit or ground point and repair them, and then eliminate short circuit or ground risks.
5. Insulation of the stator core may be partially damaged and short circuit, so there is a vortex and overheat. Treatment: please reduce the load suitability. If the generator reduces its efficiency obviously, please repair the generator stator core.
6. The bearing is short of lubricating oil. The oil number is wrong. The oil quality is bad. The bearing is installed with a wrong way or the bearing is damaged. Treatment: please find out the reason and then replace the oil or clean, adjust or replace bearing.
V. Generator rotor ground
Symptom: Generator grounding one point or two points grounding light plate light.
Fault Analysis: Generator rotor winding insulation damage, coil deformity and severe dust and greasy attached in the ends seriously are all leading to the grounding of the generator rotor windings. When the generator rotor winding grounding in one point, there is electrical current pass as the ground does not constitute an electrical circuit.
However, after one point grounded, it is easy of leading another grounding point. If any part in excitation circuit ground, it can form ground fault of two or more points ground. It is very dangerous.
After the failure, the rotor windings are short-circuited. Because of the small winding DC resistance, the excitation current will increase. So the magnetic field of generator is out of balance, and main magnetic flux reduces largely. So the STG will vibrant strongly. Meanwhile the power factor of the generator will be increased significantly and get into leading phase running (absorption of reactive power from the grid).
The stator field becomes in the frond and the rotor field becomes in the back. It will make the stator current increases. If the watcher notice that there is no excitation varying but the excitation current and stator current suddenly increases, and the excitation voltage and AC voltage are all suddenly drop, and power factor meter indicates increasing or leading phase, it means the generator rotor grounded or inter-turn short circuited. You should shut down the STG and blow-out magnetic. Please inspect the excitation system and rotor windings, and find out the short circuit point and treat it.
VI. Excitation upgrading and generator test
Excitation system upgrading, brushless exciter changes into the SCR excitation and make the generator maintenance easily. And it removes the disadvantage of brushless excitation dynamic adjustment slowly. The generator test includes stator insulation resistance test, the absorption ratio test, the iron loss test, leak test, AC and DC voltage withstand test, the rotor high speed balancing and overspeed test, dynamic and static AC impedance test, the generator no-load test, short circuit test, temperature rise test, residual pressure measurement, axis voltage measurement.
Generator Care,Steam Turbine Generator Care,Msw Power Generation,Combined Cycle Generating Unit
Shandong Qingneng Power Co., Ltd. , https://www.steamturbine.be